Golden security anti-theft Access control system with left-hand handle right 360 degree intelligent unlock fingerprint

Product introduction

This door lock uses a semiconductor live fingerprint sensor with a large amount of fingerprint storage and a resolution of up to 508 DPI. Fingerprint recording is fast, accurate and flexible. The fingerprint + key design makes setup easy. If a large change of personnel often occurs, you can easily reset the factory settings and re-record the fingerprint.

Let the door open as a pleasure.

Product function

360 ° fingerprint recognition.

Use of semiconductor live fingerprint sensor, Resolution 508 PPP. Supports 360 degree fingerprint recognition and live fingerprint recognition.RejectionFake fingerprint?

Fingerprint recording is fast, accurate and flexible.

Fingerprint storage

Fingerprint storage is large, a store with 40 fingerprints.

Super convenient installation

A new generation of smart door locks, based on different types of doors, requires only a square hole for installation. The locking core is in the handle and does not require additional holes in the locking core. Easy to install, easy to maintain, easy to operate, suitable for any type of door.

Just screw the screw and you can use it

No wiring is required for installation. The circuit board is joined in the handle. Simply screw the screw and you can use it.

Two ways to open doors

The left door and the right opening opening are combined in two opening ways. Fully satisfy your needs.

Emergency key unlock

The mechanical key is an essential accessory for emergency unlocking and equipment management. Please keep it in a safe place.

Easy factory reset

If your factory or your house changes people frequently, don’t fear. You can easily reset the factory settings with the emergency key.

Operation

The smart fingerprint lock e is highly integrated, easy to install, easy to maintain and suitable for any type of door.

1 add fingerprint: Turn the mechanical key clockwise for about 15-20 degrees and press the adjustment switch, hold it for about 3 seconds, until the blue light illuminates and releases it after the ” gave”. you will want to put a finger on the contact of the fingerprint center, such as the data collected correctly, the blue light will flash and you will hear “say” a voice that is said to record data, such as not recording the good or failure, will turn on a red light and he will hear “drops” to remember that the acquisition is not valid, in total five successful acquisition, 5 times, After completing the blue light, turn on and listen to “di ~”, a loud siren, says it adds fingerprint. The blue light flashes throughout the fingerprint entry process, but does not illuminate in several colors at the same time. Touch finger pressure requires multiple angles to pick up, Favorable database expansion, fault sensitivity is useful.

2 Remove all fingerprints: Turn the mechanical key clockwise for about 15-20 degrees and press the adjustment switch, hold it for 5 seconds (the blue light is on first and then beep 1), then , release immediately after the red light is on, the blue light is on and the sound of “Di ~” is long and all fingerprints are removed.

3 fingerprint identification to open the door: Press the fingerprint, if the fingerprint is correct, the blue light will sound 1, the motor will rotate to unlock the door, and the motor will automatically rotate 6 seconds later; If the fingerprint is not correct, the red light will sound 2 times.

4. Emergency mechanical release: Insert the mechanical key and turn counterclockwise about 45 degrees to press the handle and open the door.

5 Installation:

A. The opening diagram is shown in the package opening diagram.

B. Clutch Adjustment: Adjust the position of the clutch before installation. The adjustment method is shown in the square steel mark: turn the square steel pin to open it to the right when it is flat with the handle, and the pin opens to the left when it is perpendicular to the handle.

C s200X / S280X / S300X / S330X / S65TX left opening right adjustment: Loosen the 3 screws of the piece Limit of handle, turn the handle 180 degrees and fix it with the screw. S158X / S178X series opening left right adjustment: adjust the screw of the limit piece to the position of the limit lift handle.

S168X series opening left right adjustment: panel rotation 180 degrees to install.

Please be careful with the mechanical key, the mechanical key is an essential accessory for emergency unlocking and setting management.

The contents of the Box

Leave a comment